B2949 Engine Trouble Code

When you check engine light came on code B2949 the reason should be . However your vehicle's manufacturer may have a different definition for the B2949 OBD-II Diagnostic Body (B) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes B2949 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

B2949 Code Meaning :

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

B2949 OBD-II Diagnostic Body (B) Trouble Code Description

B2949 engine trouble code is about Ignition Coil A Primary/Secondary Circuit Malfunction. Fuel Rail/System Pressure - Too High and Engine Shutoff Solenoid Malfunction causes most of code B2949.

Reason For B2949 Code

B2949 code on vehicles with electronically controlled automatic transmissions, the 3-4 shift solenoid is responsible for actuating the hydraulic circuits to activate clutches or bands that change gears inside the automatic transmission in your car.

How To Repair B2949 Code

Before starting let's see B2949 repairing process steps:

• Qualified technicians will begin by using a scan tool to access B2949 code stored in the ECU.
• Technicians will note B2949 code present and any freeze frame data associated with them.
• After all, if you sure the engine trouble is finished, the code will be cleared.

All functions are tested, lights, gauges, central display and warning functions. Once the unit is identified as faulty, we then move onto the rebuild stage. Each unit is fully stripped, all common failing components are then replaced with versions that are higher rated than standard. Once the rebuild is complete, we then retest the instrument cluster to ensure it functions in accordance with the manufacturers original specification.

If you suspect that your car has a defective mass air flow sensor, bring it to a certified mechanic so that a whole computer diagnostic can be run. In most situations, a defective mass flow sensor has a certain code that will process throughout computer diagnostics, and is normally simple to check into with computer testing equipment.

Diagnosis Of Engine Error OBD Code B2949

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a B2949 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the B2949 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.